How to Maintain your Airsoft Gun – Make clean, Lubricate and Care

Whether yous are new to the game or a seasoned competitor, knowing basic airsoft gun maintenance tin save you time, frustration, and money.

how to maintain your airsoft gun

Caring correctly for your gun will allow it to last for y'all years, avoid unnecessary wear and tear, and help y'all when faced with technical difficulties in a game or competition.

Here are easy-to-follow steps on how to clean an airsoft gun.

How to Maintain Your Airsoft Gun

Before you lot start leaning almost maintenance, you should be enlightened nearly the common types of airsoft guns by checking out our guide on Airsoftpal. Figure out which gun you lot have, and larn how it operates. Knowing this information tin can brand it easier for you to troubleshoot when having problems with your gun, and save you money you would otherwise spend if forced to accept it to a professional.

There are two types of guns virtually common to airsoft – They are spring loaded and gas-powered.When you lot pull the trigger on a spring loaded gun, the tension in a bound is released into a BB or a pellet. This causes the gun to release the BB at a high-velocity. A spring-powered gun is limited to shooting single-burn down merely.

When the trigger is pulled in a gas-powered airsoft gun, a hammer within of the gun will push against the valve in the magazine. This causes the gas to exist released into the meridian portion of the gun, shooting the BB out of the bedroom.

How to Clean your Gun Barrel

Airsoft barrel cleaning is easy. If your BB'due south are diffusive vertically when firing your gun, information technology is fourth dimension for a proficient airsoft barrel cleaning. You lot only need a cleaning rod and paper towel to do this.

  • Thread a strip of the newspaper towel through the tip of the cleaning rod
  • Spray a silicone lubricant onto the strip
  • With the strip commencement, insert the cleaning rod into the barrel
  • Move and rotate the rod downward the barrel and repeat until clean

Check out this video for more than advice on cleaning your barrel:

Lubricate your gun

If you are having a problem with your gun misfeeding or jamming, the first thing you can do to troubleshoot is to lubricate your gun. First by removing your magazine and fire your gun in semi-car mode a few times to make certain it is free of BB's. Flip the gun upside downwardly and spray silicone oil into the hop. Leave information technology upside down for a few minutes to let the oil settle.

If the gearbox needs to be lubricated you need to remove the motor, locate the minor hole at the lesser of the gearbox, and spray the silicone oil into it. But like the hop, exit information technology upside down for a few minutes to brand certain all of the oil seeps in.

Maintenance tools

In caring for your gun you will want to use the proper tools. Proper plumbing fixtures Phillips and hex wrenches will go on screws on essential parts of the gun from stripping out. You may pay more in the long run by purchasing inexpensive tools that end upward wearing quickly and ultimately- breaking. They tin also damage your gun.

Essential tools to acquire are as follows:

  • Hex drivers– Hex head fasteners tin can be found in almost every airsoft gun. They range in sizes and it is important to detect out what the corresponding size is for your gun.
  • Screwdrivers– Stripping the heads on the screws in your gun can be detrimental. You besides need to make sure you have the right size screwdriver for your gun
  • Nut drivers– This is not necessary for all guns but can be used in securing the piston caput to the piston.
  • Hand tools– You may need to charge the battery connector to your favorite style or re-wire an AEG. In such cases, yous'll want to accept pliers and wire cutters on paw to handle it.
  • Sharps– Picks can assistance provide you with easier access to difficult to accomplish places.
  • Knife – A hobby knife can assist in etching plastic pieces.
  • Greases and oils– Keep a thick grease to lubricate your gear sets. Lithium grease tin hands exist found at well-nigh hardware stores and works well for this. For rubber components such as o-rings and hop up bucking, a silicone oil is commonly used.
  • Toolbox– Keeping track of your things volition make it easier for y'all to more effectively address your problems. Information technology will also save you a lot of money since yous will be less probable to misplace your tools.

Airsoft Magazine care

Depending on the type of gun you own, magazine intendance will vary. If you have an electric or jump airsoft gun, make sure you empty the magazine completely after each use to preserve jump strength thus, preserving the shelf-life of your gun.

If you take a gas airsoft gun, leave the magazine pressurized. Adding a drop of lubricant on the internals volition help go along all components intact. When y'all expel gas from the gun, do not use the release valve. This will cause the o-ring to freeze and can cause gas leakage in the future.

How to unjam your gun

Jams can happen for many reasons. Excessive clay or debris inside of the butt, dirty or deformed BB's, an accumulation of dirt in the magazine, damaged nozzles, or a damaged hop can all crusade the gun to jam or misfire.

If the gun is jammed, you demand to troubleshoot the problem immediately to prevent any harm. Plough off the hop upward, insert the contrary end of a cleaning rod into the barrel, plow the gun upside down, and push the BB back into the magazine. If that doesn't solve the problem it is a good idea to take the gun to a professional person.

The do's and don'ts of airsoft maintenance

DO

  1. Leave a small amount of gas in the magazine- this will proceed the o-rings lubricated when the gun is not being used for an extended menstruation of time.
  2. Make sure you make clean AND lubricate your airsoft gun every 1 to 2 months after every game or match.
  3. Avoid weakening the recoil spring by making ensuring the slide is not fully retracted for long periods of time.
  4. Avoid weakening the follower bound by emptying your magazine before letting your airsoft gun sit for a while.

DON'T

  1. Don't release all of the gas in the mag by pressing the release valve. This will lead to permanent leakage caused by deformed and frozen o-rings.
  2. Do not slam the mag into the gun. The mag lips and nozzle in the slide volition break as a issue. Your gun will then misfire.
  3. A small amount of gas left in the mag is good but a magazine left full of gas will crusade the o-rings to deform
  4. Don't operate an airsoft gas gun in cold weather condition as this hinders performance.
  5. Don't rapid fire- it will crusade the o-ring to freeze.

While learning how to make clean and maintain an airsoft gun may audio intimidating and fourth dimension consuming, it's actually very simple and helps to ensure that your weapon will be performing at its highest level, lasting you for years to come.